BOZE CNC Ti | Machining

CNC turning of case profile

CNC turning of case profile capability for titanium components

Grade 1, Grade 2, Grade 5 (Ti-6Al-4V), Grade 7, Grade 9, Grade 23 Common Grades
Up to 400 mm diameter x 1000 mm length Thickness Range
+0.01 mm (case diameter) / +0.005 mm (crystal seat) Cutting Tolerance
+0.01 mm (case diameter) / +0.005 mm (crystal seat) Tolerance
Ra 0.1 µm (mirror polish) Surface Finish
Titanium Acoustic Waveguide Extension Titanium Bell Crank Rocker Arm Titanium Bottom Bracket Shell Titanium Brake Caliper Mounting Bolt Titanium Brake Bleed Port Screw Titanium Brake Lever Pivot Pin

What is CNC turning of case profile?

CNC turning of case profile capability for titanium components

Precision machining capability for CNC turning of case profile, utilizing multi-axis CNC centers with in-process inspection and SPC quality control.

Engineering Parameters & Capabilities

CNC turning of titanium on multi-axis lathes produces cylindrical components with precision diameters and surface finishes. Live tooling enables milling and drilling in the same setup, specifically for watch case. Precision watch case for Watchmaking, Consumer present unique challenges: Cosmetic surface finish (mirror polish, brush, or bead blast) with sub-mm feature detail. Material traceability from mill to finished case.

Parameter Primary Method Alternative Method
Setup Single setup with live tooling Multiple ops required

Engineering Capabilities & Limits

Precision machining capability for CNC turning of case profile, utilizing multi-axis CNC centers with in-process inspection and SPC quality control.

Hole Types Supported

Bored holes Threaded IDs and ODs

Heat Control Measures

Minimal heat generation due to fine finishing passes. Air blast for chip clearing sufficient; coolant not required for cosmetic finishing passes.

Flatness & Stress Relief

Steady rests for long slender parts. Stress-relieved stock recommended.

Tolerance

+0.01 mm (case diameter) / +0.005 mm (crystal seat)

Typical Applications & Components

This process is used to manufacture the following titanium components.

Titanium Acoustic Waveguide Extension

Grade 5 Ti-6Al-4V (Triaxially Forged) Automotive & Motorsports

Titanium Bell Crank Rocker Arm

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Bottom Bracket Shell

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Caliper Mounting Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Bleed Port Screw

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Lever Pivot Pin

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Caliper Piston Insert

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Rotor (Disc)

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Brake Pad Retaining Pin

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Derailleur Hanger

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Derailleur Pivot Pin

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Disc Brake Rotor Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Fender Mounting Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Flat-Mount Brake Adapter

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Fork Air Chamber Top Cap

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Frame Flip Chip

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium GPS Mount Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Handlebar Grip Lock Ring

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Handlebar End Plug

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Headset Compression Plug

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Headset Crown Race

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Headset Spacer

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Headset Top Cap Screw

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Hub Freehub Body Spline

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Hydraulic Brake Banjo Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Linkage Pivot Bolt

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Main Pivot Axle

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Pedal Cleat Screw

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Pedal Spindle

Grade 5 Ti-6Al-4V Cycling / Bicycle

Titanium Pedal Traction Pin

Grade 5 Ti-6Al-4V Cycling / Bicycle

Secondary Operations & Downstream Processing

Enhance your component with our integrated downstream services:

Deburring

Manual or robotic edge finishing.

CNC Engraving (Logo/Text)

CNC Engraving (Logo/Text) for cnc turning of case profile components.

PVD Coating

PVD Coating for cnc turning of case profile components.

Water Resistance Testing

Water Resistance Testing for cnc turning of case profile components.

Quality Assurance & Inspection

Inspection Items

  • CNC turning of case profile specific dimensional verification (CMM / vision)
  • Material grade verification (PMI / OES spectrometer)

Quality Standards & Certifications

  • ISO 9001:2015 — Quality Management System
  • AS9100D — Aerospace Quality Management
  • ASTM B265 — Titanium Strip, Sheet, and Plate Standard

Frequently Asked Questions

What titanium grades are suitable for CNC turning of case profile?
CNC turning of case profile can be performed on Grade 1, Grade 2, Grade 5 (Ti-6Al-4V), Grade 7, and other grades. The specific grade selection depends on the required mechanical properties, corrosion resistance, and end-use application requirements.
What tolerances can be achieved with CNC turning of case profile?
Typical achievable tolerances for CNC turning of case profile are +0.01 mm (case diameter) / +0.005 mm (crystal seat). Tighter tolerances may be possible depending on part geometry, material condition, and quantity. Our engineering team reviews each project to determine the optimal tolerance-cost balance.
What quality certifications apply to CNC turning of case profile?
All CNC turning of case profile operations are performed under ISO 9001:2015 — Quality Management System, AS9100D — Aerospace Quality Management, ASTM B265 — Titanium Strip, Sheet, and Plate Standard certified quality management systems. Full traceability documentation, material certifications (EN 10204 3.1), and inspection reports are provided with each shipment.
What is the typical lead time for CNC turning of case profile projects?
Lead times for CNC turning of case profile vary by complexity and quantity. Prototype quantities (1-10 units) can typically be completed in 3-7 business days. Production quantities require 15-25 business days. Rush orders are available for qualifying projects. Contact our sales team for a specific timeline.
Can you provide DFM feedback for my CNC turning of case profile design?
Yes. We provide free Design for Manufacturability (DFM) analysis for all new projects. Simply upload your CAD file (STEP, DXF, or DWG format) and our engineering team will review your design and provide optimization suggestions within 24 hours.

Related Machining Capabilities

Other capabilities in the same category.

4/5-axis CNC milling

4/5-axis CNC milling capability for titanium components

5-axis CNC contour milling

5-axis CNC contour milling capability for titanium components

5-axis CNC machining of blades

5-axis CNC machining of blades capability for titanium components

5-axis CNC milling of aerofoils

5-axis CNC milling of aerofoils capability for titanium components

5-axis CNC milling of clevis brackets

5-axis CNC milling of clevis brackets capability for titanium components

5-axis CNC milling of manipulator knuckles and swivel joints

5-axis CNC milling of manipulator knuckles and swivel joints capability for titanium components

5-axis milling of faces

5-axis milling of faces capability for titanium components

5-axis simultaneous CNC milling

5-axis simultaneous CNC milling capability for titanium components

Automatic Swiss turning

Automatic Swiss turning capability for titanium components

Centerless grinding + DLC coating of actuator piston rods

Centerless grinding + DLC coating of actuator piston rods capability for titanium components

Centerless grinding of core taper

Centerless grinding of core taper capability for titanium components

CNC cutting / profile cutting

CNC cutting / profile cutting capability for titanium components
About Boze Titanium Manufacturing Center

One Metal. One Focus. Infinite Precision.

Founded in 2011 in Baoji's Titanium Valley, BOZE Metal is dedicated exclusively to titanium — from raw material to precision engineering. AS9100D, ISO 13485 & ISO 9001 certified with 500+ clients across Aerospace, Medical & Motorsport industries, we deliver end-to-end precision titanium CNC machining with full material traceability from source to component.

Boze CNC Ti is the dedicated titanium manufacturing center of Baoji Boze Metal Products Co., Ltd.

AS9100D ISO 13485 ISO 9001 500+ Clients 15+ Years OEM/ODM
Learn About Us Request a Quote
Explore More: Material Specifications Industry Applications All Services Capabilities